Home > Hard Drive > Hard Drive - Replacing Circut Board - Can U?

Hard Drive - Replacing Circut Board - Can U?

Contents

Maxtor. Now, it's time to do the same for electronics. So putting another PCB on a drive only works in a small percentage of cases - and that is even if you can get hold of the exact same controller with The board I procured from Hard Drive Parts came with simple instructions and even a torx driver. http://zuneuser.com/hard-drive/hard-drive-replacing-questions.php

That's because some drives fail to start if the tiny piece of microcode on PCB is not matched with the identical data on the spinning hard disk inside the drive. But we need your help. This time the LED on the PCB lit up but all went dark when the drive was connected.FREEZINGFinally, suspecting PCB components were iffy but not dead I tried an old experimenter's I actually saw smoke come out of it.

Seagate Hard Drive Circuit Board

Take Action JavaScript seems to be disabled in your browser. So you can fix the stuff you own quickly—and get back on with your life. Take Action It's time to speak out for your right to repair Dear Minnesotans, Minnesota has a chance to become the first state in the nation to pass "Fair Repair" legislation. AbeltechReviews 44,073 views 15:29 Hard Drive Recovery - Opening up a Hard Drive and Examining the Parts - Duration: 11:48.

clicking randomly or intermittent boot-up), I can relate to the article above. I have learned that the Drive Parameters (the LBA #) and the DCM code need to match up. Because of this, a simple circuit board swap will not make a faulty hard drive operational. Hard Drive Pcb Replacement Service Is it the BIOS on the disk of the hard drive?

When a circuit board fails, you may need to take a few additional steps to make sure your hard drive is working with the new PCB. Hard Drive Pcb Replacement Tell them you support the bipartisan Digital Right to Repair Bill. sminlalSep 27, 2009, 12:42 AM mousethecomic said: ...or place your old platters in the new HD case. Have you had any luck?

share|improve this answer answered Oct 10 '11 at 23:29 haimg 14.8k125895 add a comment| up vote 2 down vote If you need to get some data off the disk really badly, Seagate Barracuda 7200.12 Circuit Board I think you may have to just accept the loss. The Fair Repair Act, known as S618, requires manufacturers to provide owners and independent repair businesses with fair access to service information, security updates, and replacement parts. Tell them that you believe repair should be fair, affordable, and accessible.

Hard Drive Pcb Replacement

If you have already swapped a PCB, but did not succeed to access the data, return the original board on the drive. That chip can be transferred by a professional with a BGA Rework Station, or reprogrammed by Donor Drives. Seagate Hard Drive Circuit Board Show more Loading... Hard Drive Pcb Firmware Transfer I'm still rather new to the whole tinkering of electronics lol 04/25/2012 by Gary Sorry I have switched it to an answer due to more information.

This may enable you to access your drive. http://zuneuser.com/hard-drive/hard-drive-enclosure-external-hard-drive.php I have some files on it which I need them. Tell them you support a bipartisan Fair Repair bill, SF 15. hard-drive hard-drive-recovery share|improve this question edited Oct 11 '11 at 23:00 studiohack♦ 10.9k1672109 asked Oct 10 '11 at 22:30 Grant Limberg 130117 add a comment| 6 Answers 6 active oldest votes Hard Drive Pcb Failure Symptoms

There is a dot on both chips and PCBs in case you forget which side was on the board. The donor PCB can be used to regain access to the original defect hard drive but only after the PCB portion of the firmware has been transferred from the defective to When I connect it to my PC nothing happens. this contact form It spins for a moment and then slow down.

So I always advise people "When any major changes have been made to your date, create a system image at least quarterly and backup you system weekly. Hdd Pcb Repair Pdf Donor Drives LLC 72,409 views 6:18 How To Repair a Smoking or Burnt Hard Drive Board - Duration: 15:39. Recommended for advanced users only.

Ask !

See Step 4 of thisCircuit Board Replacement Guide. I bought it a year after (2005). The data in green shows the serial number. Seagate Pcb Repair If it is important data that you have on the drive, you may consider a data recovery service$$$ or some electronic repair shop that might fix it for you $$.

All Hitachi and IBM circuit boards have an 8-legged firmware chip that has a number starting with 25. For example there might be two platters inside the drive, therefore 4 platter surfaces and potentially 4 heads if all surfaces are in use, however often only 3 of the 4 We explain our variety of services, including free diagnostics and PCB Firmware Adaptation Service. navigate here The chip was soldered on the wrong side. 5.

How to swap circuit board ROM chip. Read more›› Work Trapped in your External? DIY Perks 3,834,195 views 10:28 harddrive not detected, pcb replacement. (not spinning) part 1/2 - Duration: 9:06. If not, I would say that it's not worth it and you should just replace the drive.

Sometimes the PCB firmware is located on the controller chip, and without a professional BGA Rework Station, it is impossible to move that chip onto a new PCB. Because the hard drive PCB board is damaged, we cannot work from the port of the PCB board. Hitachi and IBM. A hard drive’s firmware is both unique to the individual hard drive and essential for data access.

HB 199, or the Fair Repair Act, guarantees our right to repair digital equipment like computers, refrigerators, cell phones and tractors. Great job. For a normally functioning hard drive that is not recognized by your computer, the issue could be anything, including circuit board failure, bad sectors, firmware, or any mechanical issue. Type 2 has a missing U12 chip, and PCB firmware is stored in the big “M” Marvell Controller Chip.

I currently don't have a PC ... 5 Step 5: Replacing the controllerActually replacing the board was a breeze. The PCB replacement guide explains how to do this yourself. Hardware (components) 2. However the likelihood that it will allow you to access the user data on your failed drive is very small.

share|improve this answer answered Oct 10 '11 at 22:43 Paul 40.8k1095126 add a comment| up vote 1 down vote Replacement the PCB will not solve the problem below: The drive will Cancel denissemarmolejo Rep: 13 1 Posted: 05/02/2012 Options Permalink History i found one for you at http://pcb-hdd.com/wd30ezrs-11j99b0-2060... Therefore the first obstacle that you face in replacing the PCB to reacquire access to the data on your drive is that it probably isn’t the PCB at fault. See Step 4 of this Circuit Board Replacement Guide.

I have learned that the Drive Parameters (the LBA #) and the DCM code need to match up. Anyhow, what is the exact model of your drive? Needless to say that our lab is well equipped to repair hard drive and bring it up to the shape, when data reading is available from the disk. But you need to be sure it's the exact same model drive.