Home > Having Trouble > Having Trouble Trying To Set Up A LinkSys Wireless LAN Card W/Existing Wireless LAN

Having Trouble Trying To Set Up A LinkSys Wireless LAN Card W/Existing Wireless LAN

Contents

Consumers in Australia have statutory rights in relation to the Software and media on which the Software is provided under the Australian Consumer Law. SOME COUNTRIES, STATES AND/OR PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CERTAIN CONDITIONS, WARRANTIES OR GUARANTEES, AND/OR DO NOT ALLOW PRODUCTS OR SERVICES TO BE SOLD WITH NO WARRANTIES BELKIN, LINKSYS, WEMO and many product names and logos are trademarks of the Belkin group of companies. is there any settings besides the ones from your tutorial to make a repeater work behind another repeater? his comment is here

WPA will not work with an AP Client, Wireless Repeater and Wireless Bridge modes. My available hardware and specifications: 1.) two Wireless router (WRT54G) devices 2.) two TRENDnet TEW-AO19D 19 dBi Outdoor High-Gain Directional Antenna 3.) Distance between building is 300 meter I hope any If so, how do I configure the WAP54G, as a Wireless Bridge or Access Point? soda says: at @Carolyn, have you tried following the instructions above (ACCESS POINT MODE)?

Linksys Extender Setup

July 30, 2008 at 10:14 AM rayner said... If you modem has a private IP address 10.*.*.*. I have run this process 3 times now as a trial, and the instructions are written assuming you have a "clean" router. You only have the non-exclusive right to use the Software in accordance with this Agreement.

You can access the web interface at any time through http://10.0.133.2/ July 27, 2009 at 1:07 AM diaLogist said... PRIOR TO SUBMITTING A CLAIM FOR ARBITRATION, EITHER PARTY SHALL FIRST NOTIFY THE OTHER PARTY TO TRY TO RESOLVE THE DISPUTE. my computer can see it when I ping it I just cannot get to the setup web page to make it private. Wireless Repeater Instructions update for V24: DHCP does not work between the DHCP server in the "main" AP and the DHCP clients in computers connected to the secondary "client-bridged" WRT54G in this configuration

Let's call this WRT54G the primary. Client Bridge In very limited cases, updates may still be automatically applied, regardless of the auto-update setting. An IP address from the first router's LAN is not valid in the second router's LAN.It is important to connect those wireless routers through their LAN ports, turn off the DHCP his comment is here bobxnc note: WPA2 Personal works fine using v24sp1 on a Netgear WNDR 3300 teekay note: WPA Personal works great with an Apple Airport Extreme wireless router too.

The PC connected to my secondary router could not obtain an DHCP from my primary router. Linksys Wrt54g not set internet connection setting to anything else then DHCP, in particular do not use static IP address and do not set it to an IP address inside the main LAN For the record the master is a Netgear Rangemax 240, the second is a Leviton and the third is a Linksys BEFW11S4. See if this helps.

Client Bridge

Cisco CDP and Spanning Tree gets confused. My config is> Primary: old DI-524, client router DIR-300. Linksys Extender Setup September 10, 2008 at 5:57 AM iniabasi said... Linksys Router But in reality anyone with a little bit technical understanding or anyone desperate enough can download some easy-to-use tools which will quickly show you the SSID and the MAC addresses of

Setup Tab— Basic Setup Subtab Connection Type: Disable STP: Disable Local IP: 192.168.1.2 (it was initially 192.168.1.1) (Appears that it must/should be a valid IP in your Wireless Subnet) ***See notes this content Our goal is to provide you with a positive experience when using our apps, products and services, while at the same time keeping your Personal Information, as defined in the Belkin If you don't know those, any DNS server IP addresses will work. September 20, 2008 at 7:46 PM john928 said... Linksys Default Password

Reconnect the power to the modem and allow it reestablish a connection to the ISP. YOU ARE SOLELY RESPONSIBLE FOR (AND BELKIN DISCLAIMS) ANY AND ALL LOSS, LIABILITY, OR DAMAGES, INCLUDING TO YOUR HOME, HVAC SYSTEM, ELECTRICAL SYSTEM, PLUMBING, PRODUCT, OTHER PERIPHERALS CONNECTED TO THE PRODUCT, with same Wireless MAC addesses it worked only in WEP mode. -TEHb Encryption: Match your primary router. weblink This page requires Javascript.

FOR EXAMPLE, IN AUSTRALIA AND NEW ZEALAND, OUR SOFTWARE AND THE MEDIA ON WHICH IT IS PROVIDED COME WITH STATUTORY GUARANTEES, INCLUDING AS TO QUALITY AND FITNESS FOR PURPOSE, WHICH CANNOT Wireless Bridge I assume you have your own router aside from the WAP54G. For normal home networking with simple to use file and printer sharing it is better to connect the second router as suggested in this post...

This prevents people in your LAN consuming all your router bandwidth while accessing LAN servers.If you disable the filter, then you can access the server using the WAN IP address of

i try to use it as a repeater with a sagem router. If the wireless adapter you are using was purchased separately, consult the manufacturer's Web site for the latest software. The rights and obligations under this Agreement are not assignable by you, and any attempted assignment shall be void and without effect. Wireless Access Point Always use only one connection at a time, in particular during troubleshooting.

It only worked when I used v24 SP1 on both routers. Thanks so much for any feedback. Click save then apply. http://zuneuser.com/having-trouble/having-trouble-with-aim.php You can find the user documentation for the Software on the “Support” page of the applicable Belkin website. 2.

Select the desired network, and click Connect. I use win xpsp2or3. One of the desktops has a wireless card, the others are only there temporarily so I don't want to spend the money on them. This Agreement shall bind and inure to the benefit of the parties and their successors and permitted assigns.

please email me at djlevo7[at]msn.com anil says: at Hi Friends, I need help finding an access point / router to work with a wide range coverage like 300 - 500 meters. he's purchased a Linksys WRT54G2 wireless router for this.2 questions here. Anyone know how to make it work since it seems to be 80% there? It hasn't completely taken off, yet, and so allot of devices do not support it.

Go to an Internet URL in your browser, e.g. In other words, can I take the ethernet cable coming out of the wireless bridge and connect it to the WRT54G to create 3 more ports?Thanks! If I go back and disable security it works fine - what is the deal … does anyone know what I'm doing wrong here?? HTH Jeff says: at When configuring the WAP54G as a repeater, is a switch required?

Open a Web browser such as Internet Explorer and access any Web site. I suggest using instead something like 192.168.1.50.*** Gateway: 192.168.1.1 (ip address of your primary router) Local DNS: 192.168.1.1 (ip address of your primary router, normally it will forward your request to In Windows, open Network connections, select your LAN card, change settings, Internet Protocol (TCP/IP), properties, on the General tab choose obtain an IP address automatically, then on the Alternate Configuration tab Say it ain't so!

so looking at the switch, it is three lights blinking. tlj2:My opinion is that DD-WRT does not properly support even a single device on behing the DD-WRT "client bridge" mode radio. To turn on Public folder sharing, follow these steps: Step 1: Turn on network discovery and file sharing Turn on Network discovery and file sharing on each computer that you want The laptop stays connected to the one that you are closest to when you start the computer.